Activity in Technology and Support
Cisco Catalyst switch in ROMMON mode ("switch:" prompt) after a software upgrade
Core issueThe switch: prompt indicates that the switch has not booted completely and requires the user to complete the boot process.The reason for this problem could be an incorrect boot statement which means either the image name (IOS file name) is ...
Mesh Network - Neighbor State
Hi everyoneI'm trying understand better the neighbor states (like Update Neigh Alloc, Alloc, ect) on a mesh network running on WLC9800, but i can't find documents about.Anyone knows where i can find any documentation to understand these state ?
Cisco switch stuck at switch: prompt
I mistakenly did the factory reset-all on my Cisco 9200 switch and now the switch is only showing the switch: prompt at start-up. How do I get the switch back to where it belongs with no config and booting from the packages.conf?
Resolved! ME 8.10.196.0 Unexpected "Configuration has been changed" alert.
Hello,I have a cluster of 3802i-k9 running ME 8.10.196.0 firmware.I noticed that at the top right corner of the web dashboard, it shows "configuration has been changed" even if you just simply have a look at those stats data and made nothing change. ...
Resolved! Does HSEC-K9 license have a encrypted bandwidth limit?
Hi, I'm new to CISCO,here my question, my boss asked me if we purchase the HSEC-K9 license... what is the maximum encrypted bandwidth (HSEC-K9)? ////Does it depends on the device specs right? our device; ISR4431 with SECK9 license... where theSECK9 l...
ISR4331 traffic to ASA cause IKEv2 tunnel failure
We have been trying to configure a test Cisco ISR 4331 router to establish an IKEv2 tunnel for VPN traffic to a Cisco ASA firewall hosted by our VPN provider. Currently when the ASA initiates the tunnel with traffic, it establishes and stays up unti...
ISE deployment
Hi all, Does Cisco ISE need L3 dependency in deployment. Please give me some details ok it.
Delhi
I have cisco Anycoonect VPN dongleI am facing error "No module loaded "Pls help if it is driver issue plz send driver
Can't type anything console mode ASR
when I'm at the cisco asr console, why can't I type anything after "Press RETURN to get started!" I use a Cisco USB to USB console with a putty baud rate of 9600, can anyone help solve this problem?
Blank screen and no console access on Cisco switch
Hello: I saw that some people have this problem. I have no access to the console to my cisco 3560 switch. I can not access rommon mode too. I just have blank screen despite the fact that the serial configuration was done properly: Bits per second:960...
ISE Wildcard Cert issue
HiI have just re-added a wildcard cert to ISE as it was about to expire, when I now try connecting to guest wireless network I don tget to the portal page and i get a warning saying this web page at https://guest.boarders.co.uk :8443 could not be...
How to check router interface utilization High or low
How to check router interface utilization High or low
HOW TO Allow HTTPS through ASAv
Hi, i have topology and i want connect to google.com via browser (Https) . Although i can ping ICMP to google.com but my browser (Win7 VMware virtural machine) can't access. please help me ! ASA Version 9.9(2)!terminal width 511hostname ASA1domain-na...
ISE integration with cisco DNA
Dears, I need to understand which certificates are used between ISE and DNA, and if I do not have an internal CA how I can use the signed certificate and the DNA
How to selectively NAT through ASA in GNS3
Hi, my name is Thien.My case is that I have configuration static NAT on the ASA allowing address 3.0.0.2 (f0/0- R2) to through the ASA (g0/3 4.0.0.254)object network OUT_REALhost 3.0.0.2object network DMZhost 4.0.0.10nat (outside,DMZ) source static O...
| User | Helpful Count |
|---|---|
| 148 | |
| 134 | |
| 109 | |
| 101 | |
| 71 |
