Dear all, I was enabling PoE on a 1921 router which has EHWIC-D-8ESG-P card. The running ios is "c1900-universalk9-mz.SPA.154-3.M5.bin". I neither see any power enable command in the global nor I see anything under the interface which could enable ...
Hi.I have a Cisco Switch 3560 and not boot. The Leds: SYST, RPS, STAT, Duplx, Speed, PoE (all Leds) are always green and the POST test not run. With a serial cable connect, don't output everything for putty.IOS: Version 12.2(35)SE5Model: WS-C3560-24P...
Hi, I have a question about how the AAR SLA Class strict option works (vManage version 20.9, IOS-XE cEdges). Imagine a router with 2 colors: mpls and public-internetBy using an SLA class, you want to force FTP traffic over the public-internet color.W...
Hi, my name is Thien.My case is that I have configuration static NAT on the ASA allowing address 3.0.0.2 (f0/0- R2) to through the ASA (g0/3 4.0.0.254)object network OUT_REALhost 3.0.0.2object network DMZhost 4.0.0.10nat (outside,DMZ) source static O...
Hi, i have topology and i want connect to google.com via browser (Https) . Although i can ping ICMP to google.com but my browser (Win7 VMware virtural machine) can't access. please help me ! ASA Version 9.9(2)!terminal width 511hostname ASA1domain-na...
Hi, we have a Cisco ACI in our LAB enviroment with an older version 2.2. We'd like reset/clean all the fabric (n.3 APIC,n.2 Leaf and n.2 Spine) and restart with a new version, the 5.2. Our hardware support it We don't need the backup of actual config...
Hi, I have a "C1000-16FP-2G-L (15.2(7)E9)" device, I have enabled automatic config archive creation, but it gives the wrong time when naming. For example: While the time of my device is "10:15:19.801 +3 Thu Feb 8 2024", the name written in the archiv...
We have one webex codec plus and 3 Precistion 60 cameras. HDMI of each camera are connected to crestron switch and output of that that connected to Input of codec plus. switch of cameras are working fine but we are not able to control camera from cis...
If someone please help me to get callhome done. Thanks!"callhome test" doesn't work:3132q-v(config-callhome)# callhome testtrying to send test callhome messagewarning:no callhome message sentThe following are all I typed and errors within config-call...
We're having an issue with OSPF routing done on a Nexus9000 that we are not able to figure out. To explain the situation fully, I'm going to provide quite a bit of information, I apologize in advance. Our organization currently has several branches, ...
Hello,I'm working on a lab assignment in packet tracer and when go into any of my devices and switch from static to DHCP it shows a message stating "DHCP failed. APIPA is being used."I have no idea what this means and I'm not getting any feedback fro...
Hello Folks,I have some doubts in BGP Basics, Please clarify it.In IOS XR Is the command send-community-ebgp is the replacement for send-community both,and for send-extended-community-ebgp for send community extended?I also have another doubt in IOS ...
Hello all, I would like to get some help how to How to expend existing disk space of cisco vFMC. For example, i have 2500 GB disk at existing fmc, then i want to get increase 300 GB. I did increase at vm level to 300 GB, and i check "df -h" command i...