Activity in Technology and Support
Cisco smartnet/anyconnect error stating service provider in current location is restricting access (multiple vpn users)
Hello All, Looking for some help . All was ok up until today and nothing has changed in the server room . We have a valid contract with smartnet/any connect until Nov2020. Suddenly today my users are experiencing the attached error msg when trying t...
DHCP failed, APIPA is being used error
Hello,I'm working on a lab assignment in packet tracer and when go into any of my devices and switch from static to DHCP it shows a message stating "DHCP failed. APIPA is being used."I have no idea what this means and I'm not getting any feedback fro...
Cisco Firepower eStreamer Disconnected in Azure Sentinel unexpectedly
Hi there, i got Cisco Firepower eStreamer Disconnected unexpectedly. i don't setting anything for this eStream, but unfortunately i got disconnected. but my CEF via AMA successfully connected. i try to run "./encore.sh test" and it say success. Also...
RVS4000 Firmware Upgrade
Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
SIP refer in Direct routing sends internal Teams transfer to CUBE ?
have recently setup direct routing on CUBE with Teams following the integration guide belowhttps://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise/interoperability-portal/direct-routing-with-cube.pdfI noticed if a Teams client attempts to p...
DNS for Guest WiFi
I’m looking for some recommendations on how to set a DNS server for our Guest WIFi. My plan is to move the guest DHCP to the firewall but for DNS we need to setup a server due to third party certificate for guest portal. Any suggestions?
VLan from access port does not connected over Trunk port
Hi Cisco Community,I am fairly new to the Cisco Catalyst family and I have inherited a system which I need to upgrade/expanded/optimize.In this process I have come across a situation which is very strange (to my limited knowledge). Here it goes:I hav...
Resolved! CISCO 8540 WLC licenses
Noticed that the license is evaluation instead of perpetual? If we bought new AP, do we still need to buy licenses?Cisco wireless controller 8540Software version 8.2.151.0
Setup CBS350 Switch using an AT&T BGW320 for an Internet Connection
Hello Cisco Community!I’m an old Novell/Windows NT IT guy, who is now a technology tinkerer. Trying to understand some of these new terms, also, unfortunately, I have forgotten a good amount - as you will see in my questions below ☹. I recently purch...
Access to firmware for Cisco AP for 'non company' individual
Hi, apologies in advance if this is completely the wrong place for my question, but haven't had much luck on the main Cisco website, customer support pages.I have 2 wireless access points I'd like to reconfigure. They are both in lightweight mode and...
ASA routing protocols?
Looking for recommendations for routing traffic from ASA back to router on "inside" network so we do not have to add static routes on systems. We recently added an ASR1001 to our "inside" network that routes traffic to Amazon thru a Megaport link tha...
ISR4321 upgrade from 16.3.8 to 17.6.x
hi, We are trying upgrade IOS for a ISR4321 from 16.3.8 to 17.6.6..currently on 16.3.8 the rommon version is 16.9(1r).as part of the ios upgrade we tried to upgrade the rommon to 16.12(2r) but we get the below error when doing so.FAILURE: MD5 signatu...
Resolved! CCBU Contact
Hi I need to connect with CCBU team to show them a demo of our products to list them in market place. is there any email id or contact person whom i can reach?
Zombie Environment: "Terminate failed"
Hi All,My most recent environment is in a zombie state and it can't be extended or ended. No new environments can be launched. How, if at all possible from my end, can i clear it?
Why do I get a blank page when logging into web browser config page?
I am a CCNA student and I recently bought a SGE2000 10/100/1000 Switch to play around with. I set it up and but I am having a little difficulty getting into the switch to configure it. This switch has GUI so I opened my browser and typed in the de...
| User | Helpful Count |
|---|---|
| 147 | |
| 140 | |
| 112 | |
| 103 | |
| 71 |
